IEC60068-2-1 Temperature and Humidity Testing Chamber 1200L

IEC60068-2-1 Temperature and Humidity Testing Chamber 1200L

Complied Standards & Clauses

Conforms to IEC60068-2-1, IEC60068-2-2,IEC60068-2-78, IEC60068-2-30,etc.

Product Overview

This test chamber is used for cold, heat, humidity and dryness testing of raw materials and devices such as electronics, electricians, electrical appliances, plastics, etc. The purpose is to confirm the products reliability of storage and transportation under high and low temperature alternating heat and humidity.

Technical Parameters

Technical Parameters
Control & Operation	PLC and touch screen intelligent control system
Chamber Size	Inner Size	External Size
	1200*1000*1000 mm	1480*2150*1520 mm
Temperature Range	-40 °C ~+150°C
Humidity Range	20%～98%RH
Temperature fluctuation	±0.5℃
Humidity fluctuation	≤2.5%
Temperature deviation	≤±2.0℃
Humidity Deviation	≤±3%
Heating Rate	≧2-3°C/min
Cooling Rate	≧1°C/min, average no load
Load condition	None
Working noise	A sound level≤70dB(A) (Measured in a soundproof room with an ambient temperature of 25°C and low echo. Using A weighting, test the average of 9 points. Each test point is 1 meter away from the noise source horizontally and 1 meter above the ground.)
Temperature and Humidity Range Scheme
Structural features
Insulation enclosure structure	1. Outer wall material: A3 board spraying. 2. Inner wall material: brushed stainless steel plate SUS﹟304. 3. Chamber thermal insulation material: 100mm high temperature resistant rigid polyurethane foam. 4. Chamber door insulation material: 100mm high temperature resistant rigid polyurethane foam.
Bottom structure strength	The weight capacity of the track at the bottom of the test chamber: ≤100Kg/m² (load)
Air conditioning channel	1. Stainless steel long-axis centrifugal fans: 2 sets/90W. 2. Fan, heater, evaporator (also dehumidifier), drainage device, pressure balance port, adjustable air deflector, temperature sensor
Standard configuration of test chamber	1. Observation window: 400x600x40mm 3-layer vacuum tempered glass 2. Flat embedded handles 3. Door hinges: SUS #304 imported hinges 4. Energy-saving lamp inside the chamber 5. Lead hole: φ50mm 1 piece
Chamber door	1. Double doors open outwards, with hinges on the left and right sides and a handle in the middle (when facing the front of the box). 2. Equipped with a safety door locking mechanism (the door can be opened in the test room), the door is equipped with electric heat to prevent condensation, and the visible range of the insulating glass observation window (W400×H600mm). The door frame is equipped with an anti-condensation electric heating device.
Control panel	Controller 7-inch display screen, temperature (humidity) control display screen, operating indicator light, and lighting button.
Mechanical room	Refrigeration unit, compressor water tray, pressure relief device, heating device
Power distribution cabinet	Distribution board, cooling fan, main power switch, transformer, intermediate relay, time relay, solid-state relay, AC contactor, circuit breaker
Heater	1. Fin-type radiator-shaped stainless steel electric heater 2. Heating control method: SSR (Solid State Relay) non-contact equal period pulse width modulation 3. Heating power: approximately 3KW
Power cable hole	Located on the back of the chamber

Sinuo Testing Equipment Co., Limited established in 2019, but Sinuo has rich experience in manufacturing test euipment, test system and offering overall laboratory construction of electronic and electrical products. Sinuo's main products include electrical vehicle test equipment, battery testing equipment,  electromagnetic compatibility (EMC) test system, environmental testing equipment, fire retardant test equipment, dust-proof waterproof testing equipment and electrical appliances testing equipment. Our products covering electrical vehicle, electric power, communication, electrical appliances and electronic devices industries.

Sinuo has a professional technical research and development team, which is proficient in various international standards such AS IEC, ISO, EN, VDE, BS, AS, ASTM, GB and industry standards such AS MBN LV124, VW-80000. We master physical mechanics, heat, electricity, fluid and other theoretical knowledge in the application of equipment. And continue to focus on industry standard equipment performance optimization, operation simplification and equipment stability and reliability improvement.

Sinuo has two factories in Guangzhou and Dongguan, and cooperates with many research institutions and schools. Our R&D and production capacity are in the forefront. We have authorized agents in South Korea, the United States, South Africa, Egypt, Pakistan, the Philippines and other places, we serve customers BV, CSA, Intertek, SGS, TUV and other internationally renowned testing and certification institutions, local government quality inspection departments and production factories.